DIY Floors Standing Pull Up

🔥+ DIY Floors Standing Pull Up 12 Jul 2020 My Shed Plans - lean to shed plans - Now You Can Build ANY Shed In A Weekend Even If You've Zero Woodworking Experience! Building plans for corner ...

DIY Floors Standing Pull Up Dream and reality meet aboard the Costa Favolosa: Discover your itineraries and choose the right deck and cabin for a fabulous Favolosa holiday! ... Cabins and suites. Cabina interna Costa Fortuna ...

Wooden Sword Plans Free Blueprints

Menu
Jan for 1 last update 2020/07/12 2, 2014Jan 2, 2014 | Jamison Rantz | 15 Comments |

My son Brayden started taking an interest in building blocks so I thought a LEGO table would be a welcomed addition to his corner of or living room. Since this LEGO table would be on display for everyone to see I decided to build it out of red oak and give it a nice stain. Personally, I think it turned out beautifully but it could just as easily be built out of pine (common boards) for that rustic farmhouse look. Below I have included detailed and, as always, totally free DIY LEGO table plans. I hope you enjoy! Please post your finished projects in the brag area so I can see!

DIY Floors Standing Pull Uphow to DIY Floors Standing Pull Up for FYI, these LEGO tiles work with the Duplo LEGOs for younger kids and standard LEGOs for older kids.

Required Tools:

Materials:

*List is based on the assumption that the LEGO plates are truly 10″ x 10″. It has been brought to my attention that some may be slightly larger (1/32″ – 1/16″) Measure and if they are slightly larger or smaller you may need to adjust to fit.

Cut List:

  • 4x    2 x 2 x 18″    (Cut the 2 x 2 x 36″ stock exactly in half)
  • 4x    1 x 3 x 32″
  • 2x    1 x 4 x 37″
  • 2x    1 x 4 x 30″
  • 1x    3/4 x 30 x 30″
  • 4x    3/4″ screen moulding cut to 10″ in length with 45 degree cuts at each end

Step 1: Assemble Table Base

Step 1: Assemble Table Base

Drill two pocket holes at each end of the interior of your 1x3x30″ boards. Set them back 1/2″ from the face of your 2x2x18″ legs and screw and glue them in place using 1-1/4 pocket hole screws.

Step 2: Cut LEGO storage hole out of 30×30 plywood

Step 2: Cut hole in plywood

Now cut out the 10×10 LEGO storage opening in the center of the 30×30 plywood. I found the easiest way to draw the square accurately was to line the LEGO tile up with the outside edge and draw a line using the interior side. A cutout tool is great for this kind of thing but if you don’t have one just start out your cutout using a large drill bit at each corner and then finish off using a jigsaw.

Step 3: Add the 1×4 rail to your top.

Step 3: Attach trim rail to plywood

Drill pocket holes in each end of the 1x4x30″ boards and all around the outside edge of the plywood as shown. Screw and glue the 1×4’s to the outside edge of the plywood using 1-1/4 pocket hole screws. Then, screw the 1×4’s at the corners using 1-1/4 pocket hole screws.

DIY Floors Standing Pull Uphow to DIY Floors Standing Pull Up for Step 4: Attach the base to the top

Step 4: Attach base to top

Dill pocket holes in the base as shown in the picture. Then, with the top laying upside down, lay the base on the top and then, while maintaining 1 inch from each post to the outside of the tabletop, screw the base to the top using 1-1/4 pocket hole screws.

Step 5: Apply Finish

Now is the best time to finish your project. After installing the LEGO storage it could get a little messy! 🙂 Below is what I chose to go with but your options are limitless.

Color:

DIY Floors Standing Pull Uphow to DIY Floors Standing Pull Up for After preparing the surface of the wood, I chose to go with a Minwax dark walnut stain. The benefits of using a nice species of wood like red oak is that the stain turns out beautifully.

Sealant:

After allowing the stain to dry I chose to use a clear gloss polyurethane. I applied 5 coats evenly knocking down the surface with a 3M Between Coats Finishing Pad in between coats and after the final coat was dry I smoothed it out with the 3M Final Finishing Pad.

Step 6: Glue down the LEGO tile

Step 6: Glue the LEGO Building Plates down

Now glue down the LEGO building plates as shown using liquid nails adhesive or an equivalent. Make sure that LEGO dots on these building plates line up with the adjacent plates. If this doesn’t happen then your little one will have a hard time laying blocks across the joints.

Step 7: Add the LEGO storage



Option 1:

For this I would recommend this metal basket that I found on amazon. The sizing works out well and it can be easily secured to the bottom of the table with the use of tension clips.

DIY Floors Standing Pull Uphow to DIY Floors Standing Pull Up for Option 2:

Another option here is to use a mesh bag and staple it to the inside of the hole.

Option 3:

Are you as cheap as I am? It was a lot more work but I had a mesh metal waste bin laying around that was close in size but a little too long so I dropped it in the hole and when for 1 last update 2020/07/12 it was level drew a line and cut it around the perimeter so that it would be an exact fit.  I then stapled it to the inside of the hole.Are you as cheap as I am? It was a lot more work but I had a mesh metal waste bin laying around that was close in size but a little too long so I dropped it in the hole and when it was level drew a line and cut it around the perimeter so that it would be an exact fit.  I then stapled it to the inside of the hole.

Step 8: Trim the LEGO storage hole

Use finishing nails to attach the screen moulding to the interior of the 1 last update 2020/07/12 the LEGO storage hole to finish it off.Use finishing nails to attach the screen moulding to the interior of the LEGO storage hole to finish it off.

DIY Floors Standing Pull Uphow to DIY Floors Standing Pull Up for About The Author

DIY Floors Standing Pull Uphow to DIY Floors Standing Pull Up for Jamison Rantz

I''er like myself. In other words, I write plans for awesome looking furniture that are so easy it will blow your mind! (No woodworking experience required.)

Related Posts